![]() ![]() DSDT - I used FixShutdown because I was having problems with High Sierra not shutting down properly. Creating a Custom SSDT for USBInjectAll.kext.ġ. SSDT-UIAC.aml - a custom SSDT that is used in conjunction with RehabMan's USBInjectAll.kext.VBoxHfs-64.efi - Open-source HFS+ driver.#EmuVariableUefi-64.efi - no longer needed.Chain loads the apfs.efi driver that is already embedded in the APFS container from this container. ApfsDriverLoader-64.efi - Open source apfs.efi loader.WhateverGreen.kext - Used in conjunction with an iMac17,1 SMBIOS - prevents black screen on startup with my Nvidia GPU - amongst other things.AppleALC.kext - Needed for onboard sound to work (more details later).Lilu.kext is needed for the following two kexts to work (for best results always use the latest version of Lilu.kext and its plugins):.IntelMausiEthernet.kext - to enable my onboard Intel I219V ethernet port in macOS.USBInjectAll.kext - for USB port injection.On a 2GB USB stick I installed the latest version of Clover, customised for my build, which I would use to launch this newly-created USB Installer. Sudo /Applications/Install\ macOS\ High\ Sierra.app/Contents/Resources/createinstallmedia -volume /Volumes/Untitled -nointeraction After this, in terminal, I ran the command: Then I formatted the 16GB USB Drive as HFS+ in Disk Utility, naming it Untitled. My next step was to download the "Install macOS High Sierra.app" from the App Store using my existing install. I started by choosing a USB Stick (I settled for a 16GB Sandisk Extreme), which I was going to use for the High Sierra Installer. Boot -> Secure Boot -> Key Management -> Clear Secure Boot Keys (disables Secure Boot - only needed if this hasn't already been done)Īll other BIOS settings were left at default.Boot -> Secure Boot -> OS Type -> Other OS.Boot -> CSM (Compatibility Support Module) -> Launch CSM (Compatibility Support Module) -> Disabled.Monitor -> Q-Fan Configuration -> Q-Fan Tuning (for setting CPU & Case fan speeds automatically).(Added - Enabling this caused occasional startup kernel crashes for me, until I found this was the culprit, and needed disabling) Advanced -> System Agent (SA) Configuration -> VT-d -> Disabled.Advanced -> System Agent (SA) Configuration -> Primary Display -> PEG.I wasn't going to do a clean install - instead I was going to use a USB Stick (with the High Sierra Installer on it) to upgrade the existing OS.īIOS settings before setting off were (BIOS version used was 3504 - released ): I wanted to upgrade my current installation of Sierra to (the recently released) High Sierra. Copy the new BIOS file to a USB Drive, then use Asus' EZ Flash Utility in your BIOS to flash the new one.) You can do this by going to Asus' web-site for your motherboard and downloading the latest BIOS update. (Before starting, I made sure my BIOS was updated to the latest version. I also wanted a quiet computer, so good fan controls would be important to this build. Why the move to ASUS? I was disappointed with the poor fan controls on my previous two Gigabyte motherboards, and had heard good things about ASUS' Q-Fan system. That brings us to today, where I’m using an Asus Z170 Maximus VIII Ranger motherboard. Fast forward a couple of years, and my last Hackintosh system was built around a Gigabyte Z77X-UD4H 'board. My first Hackintosh was based around a Gigabyte GA-P55M-UD2 motherboard. Crucial BX100 250GB SSD (this is used for my macOS Drive).Corsair Vengeance LPX 16GB (2x8GB) 2666MHz Memory Kit.Asus Maximus VIII Ranger Z170 Motherboard.Usually have a HyperX ram kit installed, but currently using a G.Building a CustoMac Hackintosh: Buyer's Guide If I unplug my SSD, I also get stuck, but on error-code 99. I'm getting stuck on A2 when I start my system up, I've ruled out RAM being an issue by testing 6 previously working sticks, CPU was working fine before moving and put back into the original packaging, PSU seems to be working fine and the GPUs both seem to be fine. I'm setting up my desktop again now that I'm in my new town, but am having issues with Q-codes from my motherboard. All items except the motherboard were kept in separate antistatic bags, and all were moved by me personally to ensure they stayed safe. I recently moved, and broke my PC down into parts for the move. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |